Super Soundproofing Community Forum

Please login or register.

Login with username, password and session length
Advanced search  

News:

Need an answer right now? Go to http://soundproofing.org, or,  FEEDBACK

Or call us toll-free at 888-942-7723 8-5 Pacific time Weekdays. 

  If we're not in, send a email to supersoundproofing@gmail.com

You can get a free report on soundproofing by going  HERE

 MAINSITE

Author Topic: Sound proofing condo near airport  (Read 1011 times)

jakew

  • *
  • Posts: 0
Sound proofing condo near airport
« on: June 20, 2018, 06:42:34 AM »

Hi,

I recently moved into a new condo near an airport. Condo faces east, and jets also go east on a 1000-2000 feet height. Noise is pretty annoying (when in door, going from 40db when quiet up to 55 db, on my phone app but that may not be very accurate. In the outside my phone measures ~75db so my current window does a ~20db reduction on my phone).

The condo is already installed with double-pane window. There are 3 room facing east, and each one has a big window. Attached picture is one bedroom for which I want to try the acrylic solutions (along with the soundproofing.org supplies) and see what kind of difference it makes, before deciding on what to do with the other two rooms. This bedroom window is 58x49 inch.

I would not want to use a single heavy panel that blocks the entire window because I do want the window opening to be operable in times of need. So I was thinking to use two 3/8 panel, one covering the left part (including the opening, 58x22 overall) for easier removal, the other covering the right part (sort of permanent). As shown in the measurement picture, if I attach a panel on the middle aluminum slash, the best gap I get is around 1.3 inch. If the result is not satisfactory, I would consider attaching another whole panel of 1/8 thickness on top of that, because as you can see in the picture I do get another ~0.9 inch space to attach to a top piece of slash before it runs into the blinds. 1/8 thickness would be easier to remove.

Does this sounds too complicated or a bad plan? Is this possible without drilling holes in the frame? That is a last resort but I'm willing to try something else that does not leave holes if possible.

My situation is very similar to these two guys I think

http://supersoundproofing.com/forum/index.php/topic,4069.0.html
http://supersoundproofing.com/forum/index.php/topic,4176.0.html

Randy S

  • Senior Soundproofing Technical Specialist
  • Global Moderator
  • *****
  • Posts: 792
    • Super Soundproofing Co
Re: Sound proofing condo near airport
« Reply #1 on: June 20, 2018, 03:55:51 PM »

Ok a few things.

1) we never recommend having blinds in the dead air space, this is where heat builds up and can deform your blinds. We have no liability if this happens.
2) the problem of split panels has been a huge challenge that we have not been able to solve without having to add a 2"x4" in the middle to accommodate the mounting frame and maintain the seal and mass behind the gap...other methods we have tried normally become a weak spot or leak and greatly effects the end results.
3) as for mass vs. gap , this one is not so easy. Normally I find in field results the gap is the greatest contributor until you get into really low frequencies and increasing both ends up being the only solution based on cost vs reduction.   

In the end you must be able to create a air tight system and mass on both sides of that air space.

Based on 1" gap you should be able to achieve around STC 37-40 with 3/8" acrylic.

Hope this helps and if you decide to attempt an out of the box method please share it with our readers on this forum and let us know the results.

Good Luck.

Randy S.
760-752-3030
Randy Sieg

Super Soundproofing Co
www.soundproofing.org
888-942-7723
Ph. 760-752-3030
Fax.760-752-3040

jakew

  • *
  • Posts: 0
Re: Sound proofing condo near airport
« Reply #2 on: June 20, 2018, 04:20:52 PM »

Thank you Randy for your reply.
I don't plan to leave blinds inside the gap. If anything I may uninstall the blinds and reinstall it further away but that is too complicated for now.
As for the double pane issue, since I have a vertical aluminum bar in the middle, I plan to use that bar to install separate vertical mounting frames on the left (for the left pane) and on the right (for the right pane.) That would leave the middle aluminum bar uncovered by either pane. But the glasses will all be covered with no air leak. Would you think that the middle bar could become a weak point? (aluminum is not great in blocking sound I guess?)

STC 37-40 sounds great. I do want to use a more precise sound meter in the future to compare results. But if I can further reduce the 55db jet sound down to 40-45 that would be great. The noise is mainly jet cutting through air, so higher frequency I guess.

Randy S

  • Senior Soundproofing Technical Specialist
  • Global Moderator
  • *****
  • Posts: 792
    • Super Soundproofing Co
Re: Sound proofing condo near airport
« Reply #3 on: June 20, 2018, 04:46:26 PM »

I see what your trying to attempt, this is the same issue we deal with in commercial store fronts.

Best to use 1 piece of acrylic and not try the mount to the aluminum frame..this will also give you a larger air gap and achieve a better reduction.

if you chose to go your route you will either have to screw into the aluminum or glue the frame to it..

Randy S.
Randy Sieg

Super Soundproofing Co
www.soundproofing.org
888-942-7723
Ph. 760-752-3030
Fax.760-752-3040